If the tank is leaking, shut the water off at the cold supply valve above the heater and call (385) 488-1892. If you just have no hot water, call anyway. Dispatch is open all night, and many failures are a thermostat, an element or a thermocouple that a plumber can swap in under an hour.
Water heater repair starts with a diagnosis, not a sales pitch. We find out whether the unit has a failed part or has reached the end of its life, tell you which, and let you decide. If the tank itself is the problem, replacement is the honest answer and we say so.
Emergency signs: act before you call
Water around the base
Close the cold water valve on top of the heater. If it is a gas unit and you smell gas, leave the house and call the gas utility first.
Hissing or popping
Sediment baked onto the tank bottom makes popping. Steam hiss from the relief valve is more urgent. Turn the thermostat down and call.
Rust-colored hot water
A rusty hot tap with a clear cold tap points to corrosion inside the tank. Plan for a replacement soon.
Pilot or burner will not stay on
Do not keep relighting a gas heater that goes out again and again. Shut off the gas control and call us.
Electric tanks have a second hazard: power and water in one box. Switch off the breaker before opening any access panel. If you are unsure, leave it for the plumber.
Common water heater failures and what fixes them
| Symptom | Probable cause | Typical repair |
|---|---|---|
| No hot water at all (electric) | Tripped high-limit switch or failed upper element | Reset the switch, test and replace the element or thermostat |
| Lukewarm water that runs out fast | Failed lower element or heavy sediment | Replace the element and flush the tank |
| No hot water (gas) | Pilot out, dirty burner or worn thermocouple | Clean and relight, or replace the thermocouple or gas control |
| Water at the relief valve | Pressure or temperature too high, or a failing valve | Test the valve, check pressure and the expansion tank |
| Drips from the tank body | Corroded or cracked tank | Replacement. A leaking tank cannot be patched |
Repair or replace: a fair test
Repair makes sense when
- The leak is at a fitting, valve or drain, not the tank wall
- A single part failed on a heater under about ten years old
- The tank interior looks sound when flushed
- Hot water recovers normally once the part is replaced
Replace when
- Water seeps from the tank body or seams
- The unit is well past its expected life and rusting
- A repair would cost close to a new heater
- Hot water capacity no longer fits the household
Ask the tech what the part costs against a new unit and what the warranty covers. If you lean toward a new heater, read about installation and the option of a tankless unit before deciding.
Hard water, sediment and your tank
Draper City's 2022 report lists total hardness of 16 to 357 mg/L depending on source, and the high end counts as very hard on the USGS scale.
Minerals from hard water settle at the bottom of a tank, insulate the water from the burner or element and make the heater work harder. Flushing the tank each year slows that buildup. If your bill comes from WaterPro rather than Draper City, ask them for current hardness figures.
A sacrificial anode rod fights tank corrosion, and it wears out on a schedule. If the heater is past its warranty and the anode was never checked, the tech can inspect it during a repair visit.
Cold shower and a wet floor?
Call the 24/7 line. We work on gas and electric tank water heaters.
Utah rules for water heater work
Utah amends the model plumbing code, and those amendments require a water heater to be anchored or strapped against movement and require the pan drain to be trapped and vented. The pan also counts as an emergency receptor for leaks. Ask the Draper Building Division at (801) 576-6399 whether your job needs a permit.
What changes the price of a water heater repair
Insurance generally covers sudden and accidental water damage from a burst tank and does not cover a worn-out heater itself. Check your policy. Want your real number? Call (385) 488-1892.
Sources and standards behind this page
The strapping and drain pan points above come from the Utah amendments to the International Plumbing Code (IPC) as amended by the Utah State Construction Code in Utah Code Title 15A. They require the heater to be anchored or strapped. They also require an individually trapped and vented pan drain. Hardness figures come from Draper City's 2022 water quality report.
Straight Answers
Yes. Call (385) 488-1892 any hour. A plumber will talk you through shutting off the water supply and gas or power, then come out to diagnose the unit. You hear the price before work begins.
Sediment collects at the bottom of the tank and traps small pockets of water that boil. Flushing the tank often quiets it. Hard water speeds up the buildup.
If the pilot lights and stays lit, it is fine. If it keeps going out, there may be a thermocouple, draft or gas control problem, and repeated relighting is risky. Call us.
Dry the unit and watch where the first drop forms. Drips from the top at the pipe connections often mean a loose fitting. Water that appears from under the insulation or the bottom usually means the tank has failed.
Most element, thermostat and thermocouple repairs are done in one visit, often under two hours. A gas control valve or a part we need to order can take longer.
Utah amendments to the plumbing code call for a pan with a trapped and vented drain under certain installations, such as where a leak could damage finished space. Ask the Draper Building Division about your layout.
