If a pipe has burst, turn off the main water valve now, then call (385) 488-1892. A plumber is dispatched 24/7 to stop the flow, assess the damage and make a repair. While you wait, switch off power to wet areas only if you can reach the panel safely.
Burst pipe repair means replacing the failed section, restoring supply and checking the rest of the line for damage that will fail next. A frozen pipe that has not burst yet is also urgent, since thawing wrongly can split it.
First five minutes
Shut off the main
Turn the main valve clockwise. If you cannot find it, close the meter valve outside.
Open taps to drain
Open a faucet at the lowest point and one at the highest to relieve pressure.
Cut power near water
Turn off the breaker for any wet outlet or appliance, but only if you can reach it without stepping through water.
Move valuables
Lift furniture, electronics and paper off the floor.
Photograph everything
Take pictures of the burst and the damage before cleanup, for insurance.
Why pipes burst in Draper
Draper is at roughly 4,751 feet, with snow from November to March, so exposed pipes in garages, crawlspaces and exterior walls see real freezing. Ice does not usually split the frozen section. It builds pressure between the ice plug and a closed faucet, and the pipe bursts at the weakest point. Cold snaps after a mild stretch catch people out.
Outdoor spigots are another cause. A hose left attached in fall holds water in the bib, and a split bib leaks inside the wall once the water turns back on. WaterPro typically turns secondary irrigation water on by April 15, which is when many homeowners first learn a line split over winter.
Water still flowing?
Call now. Shut off the main first and the plumber will take it from there.
Repair options
| Pipe type | Typical repair | Notes |
|---|---|---|
| Copper | Cut out the split and sweat in a new section, or use push-fit couplings | Quick when the split is local |
| PEX | Cut and use crimp or expansion fittings | PEX tolerates some freezing but fittings can fail |
| CPVC | Replace the section with solvent-cement fittings | Old CPVC can be brittle in several places |
| Galvanized steel | Replace the section, often with newer material | Corroded pipe tends to fail again, so consider repiping |
After the repair
What to do once water is stopped
- Run water slowly and check the repaired joint for drips.
- Dry affected areas with fans and a dehumidifier within a day or two to limit mold.
- Ask the plumber to inspect nearby pipes in the same wall or space.
- Call your insurance agent early. Many policies cover sudden bursts and not gradual leaks.
- If walls or floors are soaked, discuss drying with a restoration company.
If you cannot find the source, we can trace it with leak detection. If the line coming from the street is the problem, see water line repair.
Frozen pipe that has not burst yet
Keep the faucet slightly open and warm the area with a space heater or hair dryer, working toward the faucet. Do not use an open flame. If you see a bulge or crack, shut off the water and call us.
What changes the price of a burst pipe repair
Insurance commonly pays for water damage after a sudden burst but not for the pipe wearing out. Document the damage and call your agent. Want your real number? Call (385) 488-1892.
Sources and standards behind this page
Repairs to supply piping follow the International Plumbing Code (IPC) as amended by the Utah State Construction Code in Utah Code Title 15A. After-hours contacts for Draper City and WaterPro are the numbers those providers publish, and the service boundary description comes from the Utah Division of Water Resources.
Straight Answers
Yes. Call (385) 488-1892 any hour. Shut off the main valve while you wait, and the plumber will arrive to stop the flow and repair the pipe.
Look where the water line enters the house, often in the basement, garage or a utility room, or at the meter in a box near the street. Find it before you need it.
Often, with a hair dryer or a space heater on a low setting and the faucet open. If the pipe has cracked or you cannot reach it, call us.
Many repairs take a few hours once the water is off. Pipes in a finished wall or multiple splits take longer.
Mold can start within a day or two in wet materials. Dry the area quickly, and consider a restoration company if drywall or insulation is soaked.
We repair the plumbing and can leave an access opening in the wall. Patching and painting are usually done by a drywall contractor.
